Products

This cable is a replacement part for Henkovac vacuum packaging machines — sold as the Henkovac Ribbon Cable 14 pin.

• Compatible brands: Henkovac
• Part type: Cable

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

This cable is a replacement part for Henkovac vacuum packaging machines — sold as the Henkovac Ribbon Cable 16 pin.

• Compatible brands: Henkovac
• Part type: Cable

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

The Henkovac Seal Bar Insulation Insert is a genuine replacement part for Henkovac vacuum packaging equipment.

• Compatible brands: Henkovac
• Details: This sleeve insert screws into the main part of the seal bar. The seal bar end is then bolted onto this sleeve in order to keep the seal bar end insulated from the aluminum seal bar.

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

The Henkovac Seal Bar Mechanism Spring H-2000 is a genuine replacement part for Henkovac vacuum packaging equipment.

• Compatible brands: Henkovac
• Details: This spring secures the sealbar mechanism to the top inside of the lid on H-2000 and H-3000 machines.

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

This seal wire is a replacement part for Henkovac vacuum packaging machines — sold as the Henkovac Seal Wire - Round cut-off 1.1mm.

• Compatible brands: Henkovac
• Part type: Seal wire
• Details: This wire is used in combination with the 3.5mm concave wire.

If you're unsure whether this matches your machine's model, go ahead and add it to your cart — just send us your model number afterward and we'll verify fit.

This seal wire is a replacement part for Henkovac vacuum packaging machines — sold as the Henkovac Seal Wire Concave 3.5mm.

• Compatible brands: Henkovac
• Part type: Seal wire
• Details: This sealwire is usually used in combination with the 1.1mm cut-off wire, or two concave wires side by side for a double seal.

Need help confirming fit? Add it to your cart now, then send us your machine's model number and we'll double-check compatibility right away.

This pump foot is a replacement part for Henkovac vacuum packaging machines — sold as the Henkovac Silicone Rubber.

• Compatible brands: Henkovac
• Part type: 
• Details: 17mm x 8mm Silicone Profile for Sealbar Striker Bar. Priced and sold per foot

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away. 

The Henkovac Spring Contact Plate is a genuine replacement part for Henkovac vacuum packaging equipment.

• Compatible brands: Henkovac
• Details: Used on double seal and seal/cut seal bar configurations. Two plates per seal bar are required.

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

This control board is a replacement part for Henkovac vacuum packaging machines — sold as the Henkovac Sub-Print-02 Control Board with 16 pin connector.

• Compatible brands: Henkovac
• Part type: Control board
• Details: Please note: This board has a 16 pin connector, older models may have only 14 pins. It may be necessary to replace the ribbon cable at the same time.

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

The Henkovac Vacuum Meter is a genuine replacement part for Henkovac vacuum packaging equipment.

• Compatible brands: Henkovac

Not sure this is the exact fit for your machine? Go ahead and add it to your cart, then send us your model number — we'll confirm the fit right away.

Hexagon bushing block holder with female threads, for the cushion bar.

Compatibility: Promarks DC-series double chamber vacuum sealers: DC-530, DC-640, DC-650, DC-800, DC-860 and DC-900.

Hexagon bushing with male threads, for the cushion bar.

Compatibility: Promarks DC-series double chamber vacuum sealers: DC-530, DC-800 and DC-900.

Hinge for the front control cover.

Compatibility: Promarks TM-2000 vacuum tumbler.

MSK brine injector housing without a hole for the conveyor shaft, intended for the idler side only. The bushing is not included and must be purchased separately.

Compatibility: Promarks MSK brine injectors, idler side.

MSK brine injector housing with holes for the conveyor shaft, intended for the control side only. The bushing is not included and must be purchased separately.

Compatibility: Promarks MSK brine injectors, control side.

17.5″ injector needle. The head must be 7.9mm or less.

Compatibility: Promarks MSK-32 and MSK-56 brine injecting machines.

Insulator for the seal bar end block.

Compatibility: Promarks single chamber models SC-680, SC-800 LR and double chamber models DC-530, DC-640-H, DC-650-H, DC-800, DC-860-H, DC-900.

Insulator for the seal bar end block screw.

Compatibility: Promarks TC-350; single chamber models SC-680, SC-800 LR; double chamber models DC-530, DC-640-H, DC-650-H, DC-800, DC-860-H, DC-900.

Replacement jar for the water separator on Sipromac vacuum tumblers.

Compatibility: Sipromac vacuum tumblers.

Joystick-style jog switch for manually controlling the rotation of the tub when loading and unloading the tumbler.

Compatibility: Promarks TM-150, TM-300 and TM-500 vacuum tumblers.