Products

O-ring gasket for the sanitation opening.

Compatibility: Sipromac vacuum machines.

Peel-and-stick overlay for the PD-01 PCB front panel, new style with the STOP button at the bottom right.

Compatibility: Promarks / Promax PD-01 PCB front panel.

12-button overlay for the PNC-01 board.

PCB control panel for Promarks, Promax, Bertoldi's and Aline vacuum chamber machines.

Compatibility: Promarks / Promax / Bertoldi's / Aline vacuum chamber sealers: TC-280, TC-350, TC-420, TC-520, SC-420, SC-520, SC-680, SC-800 and DC-530.

Fixed-mount phenolic plate for quick-disconnect seal bars.

Compatibility: Promarks double chamber models with quick disconnect: DC-530, DC-640-H, DC-650-H and DC-900.

Photo-eye for tumblers with serial numbers PF13102424 and later.

Compatibility: Promarks TM-150, TM-300 and TM-500 vacuum tumblers, serial number PF13102424 and after.

Photocell switch for vacuum tumblers.

Compatibility: Sipromac vacuum tumblers.

Replacement pillow block bearing.

Compatibility: Sipromac vacuum machines and tumblers.

Hinge pin, 42mm overall length. It fastens the lid hinge to the frame of the machine.

Compatibility: Promarks TC-420F/LR table top chamber vacuum sealer.

Hinge pin, 62mm overall length.

Compatibility: Promarks table top models TC-350 and TC-420, and single chamber model SC-420LR.

8mm pin that secures the air head on the brine injector. Removing two pins lets the upper air head hinge back so the injector needles can be taken out easily. Buy one pin as a replacement or two for a full set.

Compatibility: Promarks MSK-32 and MSK-56 commercial brine injectors.

Piston that sits inside the 2″ white vent valve. The vent valve lets air back into the chamber after the vacuum cycle; vacuum pressure and a spring move the piston.

Compatibility: All 2″ white valves on Promarks vacuum chamber machines.

Plug for the left side of the cushion bar.

Compatibility: Promarks DC-series double chamber vacuum sealers: DC-530, DC-640-H, DC-650-H, DC-800, DC-860-H and DC-900.

Plug for the right side of the cushion bar.

Compatibility: Promarks DC-series double chamber vacuum sealers: DC-530, DC-640-H, DC-650-H, DC-800, DC-860-H and DC-900.

Replacement plug for the lid spring, with a 45mm outer diameter and a 10mm threaded hole. The split pin is included.

Compatibility: Promarks DC800, DC860, DC900 and Koch 880 double chamber vacuum sealers.

PNC-01 digital control panel for vacuum sealers.

Compatibility: Promarks single chamber models SC-680 and SC-800 LR; double chamber models DC-530, DC-640-H, DC-650-H, DC-800, DC-860-H and DC-900; and Ultravac 880.

24V DC power supply for the MSK brine injector. It steps the voltage down to run the HMI touchscreen, taking a 220VAC input.

Compatibility: Promarks MSK brine injector.

Back-position pressure bag for DC-800 machines with offset stems built before 2012. It pushes the upper bar down against the lower cushion bar to seal the pouch.

Compatibility: Promarks DC-800 double chamber vacuum sealer with offset stems, made before 2012.

Front-position pressure bag for DC-800 machines built before 2012. It pushes the upper seal bar down against the cushion bar to seal the pouch.

Compatibility: Promarks DC-800 double chamber vacuum sealer, made before 2012.

Pressure bag that works on vacuum pressure to lift the lower cushion bar against the upper seal bar, creating a seal on the pouch.

Compatibility: Promarks SC-680 single chamber vacuum sealer.

Pressure bag that lifts the lower cushion bar against the upper seal bar to seal the pouch.

Compatibility: Promarks SC-800LR single chamber vacuum sealer.